White Upvc Reinforced Panel Raised Moulding 28mm Thick Infill

In stock
Gref
2845-2846
£50.11
White Upvc Reinforced Panel Raised Moulding 28mm Thick Infill is available to buy in increments of 1
Upvc Harewood or Fenton raised feature moulding replacement infill panel to suit white Upvc. These are a 28mm thick panel reinforced with 4mm MDF sandwiched between a dense foam to provide excellent thermal insulation and security.

Upvc Door 2 Rectangle Harewood Or 1 X Centre Square Moulded Fenton Infill Panel 28mm Thick White 

These are heavy duty UV stable door moulded raised panels used by our own installation teams since 1983 to glaze Upvc residential doors for both security and thermal installation. The panel is easily cut to size using a fine cut timber panel saw, Jig saw or if preferred circular saw. 

  • Colour: White Harewood Panel = 2 X Rectangle feature mouldings Width 680mm Height 900mm
  • Colour: White Fenton Panel = 1 X Centre feature moulding Width 690mm Height 900mm
  • Width 680mm Height 900mm
  • 28mm Thick (N:B door panels work to a 1-2mm tolerance in regard to these dimnesions)
  • Reinforced with 4mm MDF Sandwiched between foam thermal infill

Fitting Tip: Upvc door panels are not difficult to replace with only a few basic skills required:

Measure the glazing panel / glass to be replaced noting both the width and height. Measure the top bottom & middle (doing this ensures you do not get the wrong size as once you have cut it there is no going back)

If you do not have an existing panel or glass to work to then you need to measure the glazing area to be filled and allow an approximate 5mm fresh air gap all round to be able to slide the panel into. The Upvc will expand and move in hot weather so do not make it so tight it cannot move as this will increase the chance of the panel bowing cracking & DE-laminating.

Transfer the dimensions onto the panel to be cut & in the case of panels with a raised molding ensure these are centrally laid out to fit in the overall dimensions. N:B leave the protective film on the panel for marking out & cutting to prevent any marks or scratches. TIP: When you fit the panel just pull the tape back by about 30 – 40mm from all four sides in and out so that you do not trap the tape behind the gaskets when glazing up.

The panel is easily cut to size using a fine cut timber panel saw, Jig saw or if preferred circular saw. 

Removing the beads is best done with a purpose made glazing bead knife (Our part:2143 & you may find our how to do You Tube Video: Replacing A Double Glazed Unit (DGU)

Remember due to the bonding process of door panels they will always work to a 1-2mm depth tolerance. In doors that are particularly old it should be noted that the glazing gaskets will of lost some compression purely due to been compressed over such a long time and variation in seasons. If this is the issue you may need to also consider replacing the glazing gaskets as an option. Alternatively a suitable all weather sealant may be additionally required. 

Once cut to size offer the panel into the glazing area ensuring it is sat on the purpose made glazing packers that were there previously (noting the tips in the how to do video) and re-fit the glazing beads you earlier removed ensuring they go back in the same place and order you removed them.

Clean the panel and door down using either warm soapy water or Upvc cream cleaner for more stubborn marks and scuffs. N: B never clean with chemicals or abrasive materials.

More Information
Gref 2845-2846
Brand Gardinia
Backset No
Deadbolts No
Faceplate Dimensions No
Hooks No
Mushrooms No
Pinbolts No
PZ (Spindle To Key) No
Rollers No
Screw Centres No
Spindle Size No
Type No
Patio Screw Fix No
Choose Colour White Patio Handle Slim Ext Side
Locking Types No
Keep Code No
Write Your Own Review
You're reviewing:White Upvc Reinforced Panel Raised Moulding 28mm Thick Infill
Your Rating