Maco Tilt Turn Maco GU Drive Gear Various Sizes

In stock
Maco Tilt Turn Maco GU Drive Gear Various Sizes is available to buy in increments of 1

Maco GU Tilt Turn Drive Gear operates a Tilt & Turn mechanism Connects into corner drives to move locking parts round all 4 sides of the tilt turn window

Buy More Save More!

  • Order 3-5 save 5%
  • Order 6-9 save 10%
  • Order 10 and more save 15%

Savings automatically applied at basket !!

(Must be the same part, colour & size to qualify)

Tilt Turn Maco GU Drive Gear Various Sizes

  • Backset: 16mm 
  • Handle Hole Centres: 43mm 
  • Faceplate: 16mm 
  • Locking Points: GR1,1A and 2 = 0 / GR3 and 4 = 1 / GR5 = 2

The Maco drive gears were commonely made by GU and were stamped with the Maco logo we have found that in a number of situations the Maco drive gear can replace the GU one as the interlocking teeth are very similar but will always be dependant on the corner gears that the original fabricator used .

GR1 - 500-650 (Actual length before cutting = 350mm)
GR1A - 601-900 (Actual length before cutting = 580mm) Was GR2 which is now obsolete and replaced by the GR1A
GR3 - 901-1300 (Actual length before cutting = 1125mm)
GR4 - 1301-1800 (Actual length before cutting = 1520mm)
GR5 - 1801-2350 (Actual length before cutting = 2010mm)

Underneath the faceplate are teeth to connect to any Maco corner drives that may be fitted. Tilt Turn Maco GU Drive Gear Various Sizes

The old Maco drive gears you may have will likely be obsolete and superseded with the new ones shown which are now also been phased out but still in stock!

These old Maco tilt drive gears roller cams were different and recognisible because they were oval shaped not round like the newer ones shown. However the new ones will likely still fit into the keeps but it is also usal that the keep may need moving to suit the new cams and positions. This is really easy as the keeps are simply screwed into place on the outer frame. The connection teeth should still be the same and should fit once cut down.

Lastly the anti-miss handling rocker switch on the old gears is now different so again you may need to move the striker plate that forces it to close when the window is operated in the closed position. It is not unknown for some fabricators to lock and keep these new switches in the closed position and not use them as they find them very troublesome to set up, and if the window flexes and moves can prevent the window operating.

Please note that if the switch has sprung out or you need to set it back centrally then read the following:

If you look at the rocker switch you will see a “teardrop hole” above the torx head screw which is for inserting a small thin screwdriver blade or such. You will see that the double ended black spring one of the ends has flipped out of the housing and now moves in and out with the switch to make it sprung. You need to insert the screwdriver blade through the hole and flick the spring back into the housing (as per the other side that has not moved) to hold the said spring leg in situ. Now push the rocker switch that has flipped out back into the centre and it will once more be held centrally.

Fits the Maco corner drives. Search for: Maco Corner Drive Connector Tilt Turn Drive Links Top and Bottom

More Information
Gref 293-1207
Brand Maco
Backset 17mm
Faceplate Dimensions 16mm
Write Your Own Review
You're reviewing:Maco Tilt Turn Maco GU Drive Gear Various Sizes
Your Rating

You may also be interested in the following product(s)